427 lines
12 KiB
C
427 lines
12 KiB
C
//###########################################################################
|
|
//
|
|
// FILE: Example_2833xFlash.c
|
|
//
|
|
// TITLE: ePWM Timer Interrupt From Flash Example
|
|
//
|
|
//! \addtogroup f2833x_example_list
|
|
//! <h1>ePWM Timer Interrupt From Flash (flash_f28335)</h1>
|
|
//!
|
|
//! This example runs the ePWM interrupt example from flash. ePwm1 Interrupt
|
|
//! will run from RAM and puts the flash into sleep mode. ePwm2 Interrupt
|
|
//! will run from RAM and puts the flash into standby mode. ePWM3 Interrupt
|
|
//! will run from FLASH. All timers have the same period. The timers are
|
|
//! started sync'ed. An interrupt is taken on a zero event for each ePWM
|
|
//! timer.GPIO32 is toggled while in the background loop.\n
|
|
//! \b Note: \n
|
|
//! - ePWM1: takes an interrupt every event
|
|
//! - ePWM2: takes an interrupt every 2nd event
|
|
//! - ePWM3: takes an interrupt every 3rd event
|
|
//!
|
|
//! Thus the Interrupt count for ePWM1, ePWM4-ePWM6 should be equal
|
|
//! The interrupt count for ePWM2 should be about half that of ePWM1
|
|
//! and the interrupt count for ePWM3 should be about 1/3 that of ePWM1
|
|
//!
|
|
//! Follow these steps to run the program.
|
|
//! - Build the project
|
|
//! - Flash the .out file into the device.
|
|
//! - Set the hardware jumpers to boot to Flash
|
|
//! - Use the included GEL file to load the project, symbols
|
|
//! defined within the project and the variables into the watch
|
|
//! window.
|
|
//!
|
|
//! Steps that were taken to convert the ePWM example from RAM
|
|
//! to Flash execution:
|
|
//! - Change the linker cmd file to reflect the flash memory map.
|
|
//! - Make sure any initialized sections are mapped to Flash.
|
|
//! In SDFlash utility this can be checked by the View->Coff/Hex
|
|
//! status utility. Any section marked as "load" should be
|
|
//! allocated to Flash.
|
|
//! - Make sure there is a branch instruction from the entry to Flash
|
|
//! at 0x33FFF6 to the beginning of code execution. This example
|
|
//! uses the DSP2833x_CodeStartBranch.__asm file to accomplish this.
|
|
//! - Set boot mode Jumpers to "boot to Flash"
|
|
//! - For best performance from the flash, modify the waitstates
|
|
//! and enable the flash pipeline as shown in this example.
|
|
//! Note: any code that manipulates the flash waitstate and pipeline
|
|
//! control must be run from RAM. Thus these functions are located
|
|
//! in their own memory section called ramfuncs.
|
|
//!
|
|
//! \b Watch \b Variables \n
|
|
//! - EPwm1TimerIntCount
|
|
//! - EPwm2TimerIntCount
|
|
//! - EPwm3TimerIntCount
|
|
//
|
|
//###########################################################################
|
|
// $TI Release: $
|
|
// $Release Date: $
|
|
// $Copyright:
|
|
// Copyright (C) 2009-2023 Texas Instruments Incorporated - http://www.ti.com/
|
|
//
|
|
// Redistribution and use in source and binary forms, with or without
|
|
// modification, are permitted provided that the following conditions
|
|
// are met:
|
|
//
|
|
// Redistributions of source code must retain the above copyright
|
|
// notice, this list of conditions and the following disclaimer.
|
|
//
|
|
// Redistributions in binary form must reproduce the above copyright
|
|
// notice, this list of conditions and the following disclaimer in the
|
|
// documentation and/or other materials provided with the
|
|
// distribution.
|
|
//
|
|
// Neither the name of Texas Instruments Incorporated nor the names of
|
|
// its contributors may be used to endorse or promote products derived
|
|
// from this software without specific prior written permission.
|
|
//
|
|
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
|
|
// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
|
|
// OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
|
|
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
|
|
// LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
// $
|
|
//###########################################################################
|
|
|
|
//
|
|
// Included Files
|
|
//
|
|
#include "DSP28x_Project.h" // Device Headerfile and Examples Include File
|
|
#include <string.h>
|
|
|
|
//
|
|
// Defines that configure which ePWM timer interrupts are enabled at
|
|
// the PIE level: 1 = enabled, 0 = disabled
|
|
//
|
|
#define PWM1_INT_ENABLE 1
|
|
#define PWM2_INT_ENABLE 1
|
|
#define PWM3_INT_ENABLE 1
|
|
|
|
//
|
|
// Defines for the period for each timer
|
|
//
|
|
#define PWM1_TIMER_TBPRD 0x1FFF
|
|
#define PWM2_TIMER_TBPRD 0x1FFF
|
|
#define PWM3_TIMER_TBPRD 0x1FFF
|
|
|
|
//
|
|
// Make this long enough so that we can see an LED toggle
|
|
//
|
|
#define DELAY 1000000L
|
|
|
|
//
|
|
// Functions that will be run from RAM need to be assigned to
|
|
// a different section. This section will then be mapped using
|
|
// the linker cmd file.
|
|
//
|
|
#ifdef __TI_COMPILER_VERSION__
|
|
#if __TI_COMPILER_VERSION__ >= 15009000
|
|
#pragma CODE_SECTION(epwm1_timer_isr, ".TI.ramfunc");
|
|
#pragma CODE_SECTION(epwm2_timer_isr, ".TI.ramfunc");
|
|
#else
|
|
#pragma CODE_SECTION(epwm1_timer_isr, "ramfuncs");
|
|
#pragma CODE_SECTION(epwm2_timer_isr, "ramfuncs");
|
|
#endif
|
|
#endif
|
|
|
|
|
|
//
|
|
// Function Prototypes
|
|
//
|
|
__interrupt void epwm1_timer_isr(void);
|
|
__interrupt void epwm2_timer_isr(void);
|
|
__interrupt void epwm3_timer_isr(void);
|
|
void InitEPwmTimer(void);
|
|
|
|
//
|
|
// Globals
|
|
//
|
|
Uint32 EPwm1TimerIntCount;
|
|
Uint32 EPwm2TimerIntCount;
|
|
Uint32 EPwm3TimerIntCount;
|
|
Uint32 LoopCount;
|
|
|
|
//
|
|
// These are defined by the linker (see F28335.cmd)
|
|
//
|
|
extern Uint16 RamfuncsLoadStart;
|
|
extern Uint16 RamfuncsLoadEnd;
|
|
extern Uint16 RamfuncsRunStart;
|
|
extern Uint16 RamfuncsLoadSize;
|
|
|
|
//
|
|
// Main
|
|
//
|
|
void main(void)
|
|
{
|
|
//
|
|
// Step 1. Initialize System Control:
|
|
// PLL, WatchDog, enable Peripheral Clocks
|
|
// This example function is found in the DSP2833x_SysCtrl.c file.
|
|
//
|
|
InitSysCtrl();
|
|
|
|
//
|
|
// Step 2. Initialize GPIO:
|
|
// This example function is found in the DSP2833x_Gpio.c file and
|
|
// illustrates how to set the GPIO to it's default state.
|
|
//
|
|
//InitGpio(); // Skipped for this example
|
|
|
|
//
|
|
// Step 3. Clear all interrupts and initialize PIE vector table:
|
|
// Disable CPU interrupts
|
|
//
|
|
DINT;
|
|
|
|
//
|
|
// Initialize the PIE control registers to their default state.
|
|
// The default state is all PIE interrupts disabled and flags
|
|
// are cleared.
|
|
// This function is found in the DSP2833x_PieCtrl.c file.
|
|
//
|
|
InitPieCtrl();
|
|
|
|
//
|
|
// Disable CPU interrupts and clear all CPU interrupt flags
|
|
//
|
|
IER = 0x0000;
|
|
IFR = 0x0000;
|
|
|
|
//
|
|
// Initialize the PIE vector table with pointers to the shell Interrupt
|
|
// Service Routines (ISR).
|
|
// This will populate the entire table, even if the interrupt
|
|
// is not used in this example. This is useful for debug purposes.
|
|
// The shell ISR routines are found in DSP2833x_DefaultIsr.c.
|
|
// This function is found in DSP2833x_PieVect.c.
|
|
//
|
|
InitPieVectTable();
|
|
|
|
//
|
|
// Interrupts that are used in this example are re-mapped to
|
|
// ISR functions found within this file.
|
|
//
|
|
EALLOW; // This is needed to write to EALLOW protected registers
|
|
PieVectTable.EPWM1_INT = &epwm1_timer_isr;
|
|
PieVectTable.EPWM2_INT = &epwm2_timer_isr;
|
|
PieVectTable.EPWM3_INT = &epwm3_timer_isr;
|
|
EDIS; // This is needed to disable write to EALLOW protected registers
|
|
|
|
//
|
|
// Step 4. Initialize all the Device Peripherals:
|
|
// This function is found in DSP2833x_InitPeripherals.c
|
|
//
|
|
//InitPeripherals(); // Not required for this example
|
|
InitEPwmTimer(); // For this example, only initialize the ePWM Timers
|
|
|
|
//
|
|
// Step 5. User specific code, enable interrupts
|
|
//
|
|
|
|
//
|
|
// Copy time critical code and Flash setup code to RAM
|
|
// This includes the following ISR functions: epwm1_timer_isr(),
|
|
// epwm2_timer_isr(), epwm3_timer_isr and and InitFlash();
|
|
// The RamfuncsLoadStart, RamfuncsLoadEnd, and RamfuncsRunStart
|
|
// symbols are created by the linker. Refer to the F28335.cmd file.
|
|
//
|
|
memcpy(&RamfuncsRunStart, &RamfuncsLoadStart, (Uint32)&RamfuncsLoadSize);
|
|
|
|
//
|
|
// Call Flash Initialization to setup flash waitstates
|
|
// This function must reside in RAM
|
|
//
|
|
InitFlash();
|
|
|
|
//
|
|
// Initialize counters
|
|
//
|
|
EPwm1TimerIntCount = 0;
|
|
EPwm2TimerIntCount = 0;
|
|
EPwm3TimerIntCount = 0;
|
|
LoopCount = 0;
|
|
|
|
//
|
|
// Enable CPU INT3 which is connected to EPWM1-3 INT
|
|
//
|
|
IER |= M_INT3;
|
|
|
|
//
|
|
// Enable EPWM INTn in the PIE: Group 3 interrupt 1-3
|
|
//
|
|
PieCtrlRegs.PIEIER3.bit.INTx1 = PWM1_INT_ENABLE;
|
|
PieCtrlRegs.PIEIER3.bit.INTx2 = PWM2_INT_ENABLE;
|
|
PieCtrlRegs.PIEIER3.bit.INTx3 = PWM3_INT_ENABLE;
|
|
|
|
//
|
|
// Enable global Interrupts and higher priority real-time debug events
|
|
//
|
|
EINT; // Enable Global interrupt INTM
|
|
ERTM; // Enable Global realtime interrupt DBGM
|
|
|
|
//
|
|
// Step 6. IDLE loop. Just sit and loop forever (optional)
|
|
//
|
|
EALLOW;
|
|
GpioCtrlRegs.GPBMUX1.bit.GPIO32 = 0;
|
|
GpioCtrlRegs.GPBDIR.bit.GPIO32 = 1;
|
|
EDIS;
|
|
|
|
for(;;)
|
|
{
|
|
//
|
|
// This loop will be interrupted, so the overall
|
|
// delay between pin toggles will be longer.
|
|
//
|
|
DELAY_US(DELAY);
|
|
LoopCount++;
|
|
GpioDataRegs.GPBTOGGLE.bit.GPIO32 = 1;
|
|
}
|
|
}
|
|
|
|
//
|
|
// InitEPwmTimer -
|
|
//
|
|
void
|
|
InitEPwmTimer()
|
|
{
|
|
EALLOW;
|
|
SysCtrlRegs.PCLKCR0.bit.TBCLKSYNC = 0; // Stop all the TB clocks
|
|
EDIS;
|
|
|
|
//
|
|
// Setup Sync
|
|
//
|
|
EPwm1Regs.TBCTL.bit.SYNCOSEL = TB_SYNC_IN; // Pass through
|
|
EPwm2Regs.TBCTL.bit.SYNCOSEL = TB_SYNC_IN; // Pass through
|
|
EPwm3Regs.TBCTL.bit.SYNCOSEL = TB_SYNC_IN; // Pass through
|
|
|
|
//
|
|
// Allow each timer to be sync'ed
|
|
//
|
|
EPwm1Regs.TBCTL.bit.PHSEN = TB_ENABLE;
|
|
EPwm2Regs.TBCTL.bit.PHSEN = TB_ENABLE;
|
|
EPwm3Regs.TBCTL.bit.PHSEN = TB_ENABLE;
|
|
|
|
EPwm1Regs.TBPHS.half.TBPHS = 100;
|
|
EPwm2Regs.TBPHS.half.TBPHS = 200;
|
|
EPwm3Regs.TBPHS.half.TBPHS = 300;
|
|
|
|
EPwm1Regs.TBPRD = PWM1_TIMER_TBPRD;
|
|
EPwm1Regs.TBCTL.bit.CTRMODE = TB_COUNT_UP; // Count up
|
|
EPwm1Regs.ETSEL.bit.INTSEL = ET_CTR_ZERO; // Select INT on Zero event
|
|
EPwm1Regs.ETSEL.bit.INTEN = PWM1_INT_ENABLE; // Enable INT
|
|
EPwm1Regs.ETPS.bit.INTPRD = ET_1ST; // Generate INT on 1st event
|
|
|
|
|
|
EPwm2Regs.TBPRD = PWM2_TIMER_TBPRD;
|
|
EPwm2Regs.TBCTL.bit.CTRMODE = TB_COUNT_UP; // Count up
|
|
EPwm2Regs.ETSEL.bit.INTSEL = ET_CTR_ZERO; // Enable INT on Zero event
|
|
EPwm2Regs.ETSEL.bit.INTEN = PWM2_INT_ENABLE; // Enable INT
|
|
EPwm2Regs.ETPS.bit.INTPRD = ET_2ND; // Generate INT on 2nd event
|
|
|
|
|
|
EPwm3Regs.TBPRD = PWM3_TIMER_TBPRD;
|
|
EPwm3Regs.TBCTL.bit.CTRMODE = TB_COUNT_UP; // Count up
|
|
EPwm3Regs.ETSEL.bit.INTSEL = ET_CTR_ZERO; // Enable INT on Zero event
|
|
EPwm3Regs.ETSEL.bit.INTEN = PWM3_INT_ENABLE; // Enable INT
|
|
EPwm3Regs.ETPS.bit.INTPRD = ET_3RD; // Generate INT on 3rd event
|
|
|
|
EALLOW;
|
|
SysCtrlRegs.PCLKCR0.bit.TBCLKSYNC = 1; // Start all the timers synced
|
|
EDIS;
|
|
}
|
|
|
|
//
|
|
// epwm1_timer_isr -This ISR MUST be executed from RAM as it will put the Flash
|
|
// into Sleep Interrupt routines uses in this example
|
|
//
|
|
__interrupt void
|
|
epwm1_timer_isr(void)
|
|
{
|
|
//
|
|
// Put the Flash to sleep
|
|
//
|
|
EALLOW;
|
|
FlashRegs.FPWR.bit.PWR = FLASH_SLEEP;
|
|
EDIS;
|
|
EPwm1TimerIntCount++;
|
|
|
|
//
|
|
// Clear INT flag for this timer
|
|
//
|
|
EPwm1Regs.ETCLR.bit.INT = 1;
|
|
|
|
//
|
|
// Acknowledge this interrupt to receive more interrupts from group 3
|
|
//
|
|
PieCtrlRegs.PIEACK.all = PIEACK_GROUP3;
|
|
}
|
|
|
|
//
|
|
// epwm2_timer_isr - This ISR MUST be executed from RAM as it will put the
|
|
// Flash into Standby
|
|
//
|
|
__interrupt void
|
|
epwm2_timer_isr(void)
|
|
{
|
|
EPwm2TimerIntCount++;
|
|
|
|
//
|
|
// Put the Flash into standby
|
|
//
|
|
EALLOW;
|
|
FlashRegs.FPWR.bit.PWR = FLASH_STANDBY;
|
|
EDIS;
|
|
|
|
//
|
|
// Clear INT flag for this timer
|
|
//
|
|
EPwm2Regs.ETCLR.bit.INT = 1;
|
|
|
|
//
|
|
// Acknowledge this interrupt to receive more interrupts from group 3
|
|
//
|
|
PieCtrlRegs.PIEACK.all = PIEACK_GROUP3;
|
|
}
|
|
|
|
//
|
|
// epwm3_timer_isr -
|
|
//
|
|
__interrupt void
|
|
epwm3_timer_isr(void)
|
|
{
|
|
Uint16 i;
|
|
|
|
EPwm3TimerIntCount++;
|
|
|
|
//
|
|
// Short Delay to simulate some ISR Code
|
|
//
|
|
for(i = 1; i < 0x01FF; i++)
|
|
{
|
|
|
|
}
|
|
|
|
//
|
|
// Clear INT flag for this timer
|
|
//
|
|
EPwm3Regs.ETCLR.bit.INT = 1;
|
|
|
|
//
|
|
// Acknowledge this interrupt to receive more interrupts from group 3
|
|
//
|
|
PieCtrlRegs.PIEACK.all = PIEACK_GROUP3;
|
|
}
|
|
|
|
//
|
|
// End of File
|
|
//
|
|
|